Bosch glue pen teardown


My cheap plug in hot glue gun died and looking for a replacement I found this: the Bosch GluePen

What does it do? it’s a hot glue gun for 7 mm glue sticks that warms up in 15 seconds. Charges via micro USB.

Much better than my old one that needed ~5 minutes to warm up for probably half a minute of gluing. I am very happy because of the fast warm up, wireless operation and small size. Battery should last 30 minutes and you get the low warning when there is 1/3 left, which I find enough.

You can grab one from paying the same low price and helping support my website (Disclaimer!).

What’s inside?

Two screws later

The whole “mechanism” detaches from the sides

Let’s look in more detail on the PCB

The whole thing is controlled by an ATTINY24A microcontroller.

On the left side next to the micro USB there is a charger circuit labeled ‘3303’. On the top of the micro there appears to be a NTC used to monitor the temperature during charging. The holes are probably there in case a through hole termistor is used.

On the right side we can see the fuse and a IRF3711Z 6mΩ 20V HEXFET driving the heating element. At the glue melting end there is no temperature sensor, they are probably relying on the positive thermal coefficient of the heating element to achieve a rather stable temperature, as the manual quotes “approximately 170 °C”. Also there is a step up converter – used to generate ~12 V to drive the gate of the tranzistor, to keep it in the low ohmic region.

There does not appear to be any form of electronic temperature regulation – even after 3 minutes since I turned it ON the device maintains 12 V constantly at the gate of the tranzistor, no PWM or anything.

The wire going to the heating element is also connected to the micro, possibly to measure something, but what? Also the current through the battery while charging seems monitored by the micro as well, through the 0.22 Ω resistor next to the blue wire.

The battery is a 18650 made by Samsung, 1.5 Ah.

Checking the back of the PCB when…. what? Steinel? There appears to be a similar one.

The device charges via micro USB and does come with a 500 mA charger. While I can understand Bosch including one for comfort, for me this will go into the big pile of chargers that I might find some other purpose for. I simply have plenty of other chargers around the house for randomly charging whatever micro USB device needs to. Not to mention the 10 port Anker one on my desk which you can find at (Disclaimer!)


The device seems well built, has a good price and I am happy with it so far. It’s much faster to warm up compared to my old one which makes gluing faster.

You can grab one from paying the same low price and helping support my website (Disclaimer!).

Bookmark the permalink.


  1. Pingback: Inside the Bosch Glue Pen: Dissecting Design and Functionality

  2. Sami Onur Zaim

    I need to replace the fuse. Is the fuse a 15A one? any 15A fuse will work?

  3. can anyone tell me what size capacitor is right after the micro usb. I used the wrong power supply and it popped off then disappeared. I am hoping to repair the pen.

    • I think that if that capacitor is blown, the rest of the electronics might be too. That is a ceramic capacitor, it is not polarity dependent, so if you applied reverse polarity the rest is probably dead. Sorry to hear that 🙁
      It is very likely the circuits would work without it, to some extent.

  4. There’re 3000+ mAh cells available specified for about 20A discharge

  5. Where is made this gluePen? Roumania or Hungary ?

  6. my glue pen had ceased to work and I took it apart.
    I found the rubber washer had shrunk and would no longer allow the 7mm glue stick through.

    Removed it, doesn’t seem to serve much purpose.

    I found this site after the fact, but it is interesting to see your observations.

  7. Exactly, modern 18650 cells have even more than double the capacity.
    They also sell a bigge version, such a shame that one still has the same small battery.

  8. Thanks. Now i know it’ll be easy to increase runtime 🙂

    • 18650 cells come in different varieties: high capacity or high current (and low capacity crappy ones).
      A typical 2500-3000mAh cell is good for 2C discharge (5-6A), the high current cells can deliver much more, like 10C sometimes also 20-30A.

Leave a Reply to Bogdan Cancel reply

Your email address will not be published. Required fields are marked *


This site uses Akismet to reduce spam. Learn how your comment data is processed.